Examples



mdbootstrap.com



 
Статья
2019

Structure and Mechanical Properties of 3D-Printed Ceramic Specimens


V. V. PromakhovV. V. Promakhov, A. S. ZhukovA. S. Zhukov, A. B. VorozhtsovA. B. Vorozhtsov, N. A. SchultsN. A. Schults, S. V. KovalchukS. V. Kovalchuk, S. V. KozhevnikovS. V. Kozhevnikov, A. V. OlisovA. V. Olisov, V. A. KlimenkoV. A. Klimenko
Российский физический журнал
https://doi.org/10.1007/s11182-019-01790-0
Abstract / Full Text

The paper presents the research results of the structure, phase composition and mechanical properties of aluminum oxide ceramic specimens obtained by the additive manufacturing technology. The manufacturing process and the original equipment are described. The formation of several types of pores and surface boundaries between the layers is shown during ceramic 3D printing. It is found that for the different printing strategies, the different mechanical properties are observed in the obtained specimens that are stipulated by the structural anisotropy.

Author information
  • National Research Tomsk State University, Tomsk, RussiaV. V. Promakhov, A. S. Zhukov, A. B. Vorozhtsov, N. A. Schults, S. V. Kovalchuk, A. V. Olisov & V. A. Klimenko
  • Belgorod State Technological University named after V.G. Shukhov, Belgorod, RussiaS. V. Kozhevnikov
References
  1. J. Deckers, J. Vleugels, and J. Kruth, J. Ceram. Sci. Techn., 5, 245–260 (2014).
  2. V. Promakhov, I. Zhukov, S. Vorozhtsov, et al., Refract. Ind. Ceram., 56, No. 6, 610–614 (2016).
  3. V. Promakhov, et al., AIP Publ., 1772, (2016)
  4. I. Gibson, D. W. Rosen, and B. Strucker, Additive Manufacturing Technologies, Springer, New York (2010).
  5. L. Thijs, et al., Acta Mater., 58, No. 9, 3303–3312 (2010).
  6. J. Alcisto, et al., J. Mater. Eng. Perform., 20, No. 2, 203–212 (2011).
  7. T. Wang, et al., J. Alloys Compd., 632, 505–513 (2010).
  8. B. Baufeld, et al., Mater. Des., 31, 106–111 (2010).
  9. J. Gonzalez-Gutierrez, S. Cano, S. Schuschnigg, et al., Materials, 11, 840 (2018).
  10. C. Bae and J. Halloran, Int. J. Appl. Ceram. Technol., 8, No. 6, 1255–1262 (2011).
  11. W. Zhou, D. Li, and H. Wang, Rapid Prototyping J., 16, No. 1, 29–35 (2010).
  12. M. Schwentenwein, P. Schneider, and J. Hpma, Adv. Sci. Technol., 88, 60–64 (2014).
  13. V. Promakhov, et al., Materials, 11, 2361 (2018).
  14. A. A. Kozulin, A. S. Narikovich, V. D. Aliev, et al., Izv. Vyssh. Uchebn. Zaved., Fiz., 59, No. 7/2, 108–112 (2016).
  15. P. Zhang, J. Liu, and A. To, Scripta Mater., 135, 148–152 (2017).
  16. S. Wolf, T. Lee, E. Faierson, et al., J. Manuf. Process., 24, 397–405 (2016).